Substrate Preparation
The surface should be sound, clean, free from loose
material, grease, laitance, dirt curing compound, etc.
Before the Vetonit Crack Filler application, wet the
entire surfaces with clean potable water and allow the
surfaces to become damp at the application time.
Mixing
For mechanical mixing, add to the mixing container
9.5-11.0 liters of water for each 25Kg bag of Vetonit
Crack Filler or 0.57-0.66 litres/1.5kg small bag. Add the
Vetonit Crack Filler
High quality premixed surface crack
filler
Product Description
www.saveto.com
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any
liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how
its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the
right to change any of the Technical Data Sheets specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and
new 3rd party testing; kindly refer to our website for the latest updated TDSs.
LEGAL DISCLAIMER
Technical Data Sheet
Product Data Sheet Construction Materials
Ref No.: G6-WT001-07-23 KSA
-Vetonit Crack Filler
powder to the water and mix with a mechanical plaster
mixer, or mix using a low-speed electric drill fitted with
a suitable paddle for 3-4 minutes until achieving a
uniform, lump-free consistency.
Leave the mixed material to stand for 10 min and
briefly remix without the addition of water. Mix small
batch quantities manually for approx. 1-2 min or until
achieving a homogenous mix.
When required, add 0.5 liters of Vetonit Bond 2 to
the mixing water, and accordingly adjust the water
requirement for each 25kg bag, or 30ml of Vetonit Bond
2 per 1.5kg bag. Follow the same mixing procedure as
above.
Use the mixed material within 2 hours.
Do not add water once the mixed material starts to
stiffen or harden.
Application
Apply Vetonit Crack Filler in two coats for wide and
deeper cracks.
Apply Vetonit Crack Filler to the substrate by pressing
the filler firmly into the cracks using a flat putty trowel.
After treating cracks with Vetonit Crack Filler, it is
recommended to use Vetonit Joint Tape 50mm or
100mm wide . For better adhesion, use Vetonit Bond 2
when fixing the tape.
Use alkali-resistant paints and coatings as a final
decorative finish.
Curing
Vetonit Crack Filler generally may not require curing.
However, in extreme weather conditions (T > 45 C° and
RH < 50% ), cure Vetonit Crack Filler by spraying the
surface with clean water every 8-12 Hrs, for a minimum
of 2 days.
Cleaning
Clean all the tools immediately after finishing by water.
Clean hardened materials mechanically.
Packaging & Coverage
Stated consumption data are for general guidance.
Actual consumption depends on the nature of the
substrate, method of application, and wastage.
Shelf Life & Storage
The original sealed bags of Vetonit Crack Filler have
a shelf life of 12 months provided it is stored clear of
ground in a dry, shaded place below 35oC.
Health & Safety
Vetonit Finish WR is highly alkaline; therefore, avoid
direct contact with eyes or skin. It is recommended to
use protective gloves and goggles during application.
In case of any skin contact, wash it with soap & water. In
case of eye irritation, immediately wash with a copious
amount of clean cold water. Seek medical advice.
Vetonit Finish WR is non-flammable.
For further information, please refer to the material
safety data sheet.
Additional Information
Saveto manufactures a wide range of construction
chemicals and specialty products for various
applications divided into the following product groups:
- Waterproofing.
- Concrete Repair & Grouts.
- Flooring Systems.
- Wall & Facade Systems.
- Sealants and Joints.
- Putties & Finishes
- Plasters & Renders.
- Tiling Systems
- Primers & Ancillary Products.
- Thermal Insulation Systems.
- Protective Coatings.
- Accessories
Saveto also provides various technical information
such as CAD details, detailed method statements,
specification clauses, application manuals, product
selectors and technical support both in contractors
and consultants’ offices as well as construction sites.
For further information on these products and systems,
kindly check our website or contact your local Saveto
representative.
